<kbd id='xffni'></kbd><address id='mdkeo'><style id='fzguu'></style></address><button id='ndtxf'></button>

          环亚ag旗舰厅是專業的[【熱風爐】生產廠家!

          常州ag环亚娱乐平台能源科技有限公司

          示例圖片三
          網站首頁 > 行業資訊 > 環保新聞

          环亚APP下载-ag88环亚娱乐-首页

          保養好單層玻璃,讓其在使用中少出現故障,同是讓您也省去了不少煩惱。在日常的操作使用中,如何更好的應用單層玻璃,使其發揮它的最大價值。這時候您就不得不了解單層玻璃是如何保養的? 1、用前仔細檢查儀器,玻璃瓶是否有破損,各接口是否吻合,注意輕拿輕放。

          Maintenance of single-layer glass condenser, so that it rarely fails in use, the same allows you to save a lot of trouble. In daily operation and use, how to better apply single-layer glass condenser to make it play its maximum value. At this point, you have to understand how the single-layer glass condenser is maintained? 1. Check the instrument carefully before use. Whether the glass bottle is damaged or not, and whether the interfaces are identical. Take care to handle it lightly. 2、用軟布(可用餐巾紙替代)擦拭各接口,然後涂抹少許真空脂。(真空脂用後一定要蓋好,防止灰砂進入。)

          2. Wipe the interfaces with soft cloth (napkins can be used instead) and then apply a little vacuum grease. (Vacuum grease must be well covered to prevent sand from entering.)

          3、單層玻璃各接口不可擰得太緊,要定期松動活絡,避免長期緊鎖導致連接器咬死。

          3. The interface of single-layer glass condenser should not be tightened too tightly, so loosen the loosening collar regularly to avoid the long-term locking leading to the connector biting.

          4、先開電源開關,然後讓機器由慢到快運轉,停機時要使機器處于停止狀態,再關開關。

          4. Turn on the power switch first, and then let the machine run from slow to fast. When the machine stops, turn off the switch.

          5、各處的聚四氟開關不能過力擰緊,容易損壞玻璃。

          5. Polytetrafluoro switches everywhere should not be tightened too tightly, which is easy to damage the glass.

          6、每次使用完畢必須用軟布擦淨留在機器表面的各種油跡,污漬,溶劑剩留,保持清潔。

          6. After each use, all kinds of oil marks, stains and solvents left on the surface of the machine must be wiped off with a soft cloth to keep it clean.

          7、停機後擰松各聚四氟開關,長期靜止在工作狀態會使聚四氟活塞變形。

          7. The PTFE piston will be deformed if the PTFE switches are unscrewed after shutdown, and the PTFE piston will be stationary for a long time.

          8、定期對密封圈進行清潔,方法是︰取下密封圈,檢查軸上是否積有污垢,用軟布擦干淨,然後涂少許真空脂,重新裝上即可,保持軸與密封圈滑潤。

          8. Clean the sealing ring regularly by removing the sealing ring, checking whether there is dirt on the shaft, wiping it with a soft cloth, then applying a little vacuum grease and reloading it to keep the shaft and sealing ring smooth.

          9、電氣部分切不可進水,嚴禁受潮。

          9. Electrical parts must not be flooded and damp is strictly prohibited.

          10、必須采購原廠正宗配件,隨意使用其他配件對機器會造成致命的損害。

          10. Authentic parts must be purchased from the original factory. The use of other parts at will will will cause fatal damage to the machine.

          11、對單層玻璃做任何修理或檢查時,一定要先切斷電源,水源。

          11. When repairing or inspecting a single-layer glass condenser, the power supply and water source must be cut off first.

          辛苦整理!轉載請注明來自 #n1b/3025.html



          標簽:   熱風爐 冷凝器 熱風爐廠家 环亚APP下载熱風爐 ag88环亚娱乐熱風爐